Сглобка на сонда за сензор за терморезистор в Китай за контрол на температурата

An NTC thermistor is a temperature sensor that uses the resistance properties of ceramic/metal composites to measure the temperature. Our full spectrum NTC thermistor is a resistance thermometer, or a resistor whose resistance is dependent on temperature. The term is a combination of “thermal” and “resistor”. It is made of metallic oxides, pressed into a bead, disk, or cylindrical shape and then encapsulated with an impermeable material such as epoxy or glass. Производител на сонди за резисторни сензори от висок клас — YAXUN е специализирана в термистори с температурна чувствителност и квалифицирани по AEC-Q200. TCTR – NTC дебелослоен термистор. 47-1.6MΩ. Най-строга толерантност 1%. B Стойност 2410K – 4800К.
Сензор за температура на термистора — базирани на силиций линейни термистори на същата цена и размер като традиционните NTC термистори. Постигнете надеждност на системата с висока точност с най-малките линейни термистори в индустрията.
Field-proven thermistor level-sensing technology with NPT mounting threads;
SP-M models temperature sensor are designed for use with ST-15 Control Monitors Electrical appliances, автомобили, авиация, small household appliances, toys;
Typical uses include storage tanks, double-containment piping trenches, and double-wall storage tank interstitial space monitoring;
Years of dependable, virtually maintenance-free operation;
Sensors can be easily extended to desired length at installation site using a 3/8” x 3/8” coupler and the required length of 3/8” NPT pipe.

Ender 3 Thermistor Sensor, Upgrade HT-NTC100K 3D Printer Thermistor Sensor: Thermistor temperature sensor. Metal head diameter: 3 мм, head length: 15 мм,cable wire length: 1 метър,конектор: XH2.54 2PIN, （Suitable for heating blocks with holes of 3 mm*15 mm-3 mm*20 mm）;
Widly Compatibility: Product recommended operating temperature -50 °C ~ +280 °C, can replace the cartridge K-type thermocouple temperature sensor. Compatible with the heatblocks with 3 mm hole,като например: V6 Volcano PT100 type heated block, и т.н;
Sensors is accurate: The best feature was the flexible and heat shielded probe leads to the copper sensor. Unlike the other with a nickel plated probe/heat shrink, this can be fitted in very tight spots without worry. Be sure you redo your PID calibration;
Long Service Life: Compared with the same type that are insulated with ordinary heat shrinkable tubes, ours uses glass fiber with a temp resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temp work;
Fit ALL-METAL HOTEND: Work for E3D-V6 Volcano PT100 Ender 3 series all-metal hotend such as spider-hotend,K1-red-Lizard-hotend,dragonfly-hot-end,voron-hotend etc.

3D Термистор за принтер 100k NTC 3950 с 1 Използване на удължен кабелен проводник за Ender 3 V2 Pro CR10 и друг екструдер за 3D принтер Hotend

Heater NTC thermistor: with M3 Thread Stud thermistor，Fast-Plug Connector Compatible with 3/3 V2/3 Neo/3 V2 Neo/3S/3 PRO/5/5

Термисторен сензор NTC100K за Creality 3 v2 Upgrade 3x15mm 3950 Съвместим с термистор

Radial Leaded Resin Coated NTC Thermistor Features
High measurement accuracy.
Tight tolerance on resistance and Beta value.
Fast response, small dimension.
Can operate in long time stability.
Nominal resistance @25C can be from R25 1kΩ–1000kΩ.
Typical resistance at 25C R25 1k ohm, 2k ома, 2252 ohm, 3k ома, 4.7k ома, 5k ома, 6.8k ома, 10k ома, 15k ома, 20k ома, 30k ома, 40k ома, 47k ома, 50k ома, 100k ома, 150k ома, 1000k ома, и т.н.
Коефициент на разсейване: ≥3.0 mW/C in still air.
Термична времеконстанта: ≤12 seconds in still air.
Диапазон на работната температура: -45C — +125C.

Notes：□ in the part number for filling in resistance tolerance,
optional for ±1%(Е), ±2%(G), ±3%(З), or ±5%(Дж).