продуктови категории
- Държач на кутия с предпазители 36
- Температурен сензор 30
- Термоключ 58
- Автомобилен предпазител 19
- Предпазители с болтове 7
- термичен предпазител 29
- предпазители за повърхностен монтаж 12
- термистор 1
- Държач за предпазител за монтаж на печатна платка 27
- Окабеляване 1
- Държачи за ножови предпазители 17
- термостат 34
- Електрически предпазител 14
- Термичен прекъсвач 20
Продуктови етикети
брониран сензор за термодвойки
ножов държач за предпазител
Автомобилен ножов предпазител
Автомобилен предпазител
Предпазител от керамична тръба
Прекъсвач
Дискови термостати
Ds18b20 температурен сензор
електрически предпазител
Бързо/бавно работещ предпазител
Държач на кутия с предпазители
Предпазител от стъклена тръба
Вграден държач за предпазител
Термостат Limit Snap Disc
Мини автоматични прекъсвачи
Защита от претоварване на двигателя
Термична защита на двигателя
NTC сензор
NTC термисторен сензор
Държач за предпазител за монтаж на печатна платка
PPTC възстановяем предпазител
PT100 Температурен датчик
PTC термистор
съединител на сензора
Сензорни сонди & Кабели
Микро предпазител с бавен удар
Предпазители за повърхностен монтаж
Връзка за изключване на темп
Превключвател за контрол на температурата
Температурен предпазител
Температурен сензор
Кабел за температурен датчик
Сонда за температурен сензор
температурен ключ
Термично прекъсване
Превключвател за термично изключване
Термичен предпазител
термичен протектор
Термоключ
Термисторна сензорна сонда
SEFUSE NEC SF Cutoffs Thermal Fuse OEM/ODM Service
Категория: термичен предпазител
Тагове: Превключвател за термично изключване, Термично прекъсване, Термичен предпазител
How to tell if a sefuse NEC temperature fuse (Термичен предпазител) is good or bad?
The following steps can be used to measure the quality of a temperature fuse (Термичен предпазител) :
Use a multimeter to measure the resistance value: Set the multimeter to the resistance value measurement position, and then connect two test pens to the two ends of the Thermal Fuse . If the fuse is not blown, its resistance value should be very small. If the fuse is blown, the resistance value will be a larger number. If you are not sure about the correct resistance value, you can refer to the product manual or consult the manufacturer.
Observe the color change: If the Thermal Fuse turns black or the resistance value is abnormally high, it needs to be replaced.
The following matters need to be noted during the measurement process:
Lead bending: When bending the lead, it should be bent from a part more than 6 mm away from the root, and the root and lead should not be damaged. Do not forcibly pull, press, or twist the lead.
Welding operation: When welding the lead, the heating humidity should be limited to a minimum, and be careful not to apply high temperature to the thermal fuse. Do not forcibly pull, press, or twist the thermal fuse and lead. After welding, it should be cooled for more than 30 seconds immediately.
Use conditions: Thermal fuses can only be used under the conditions of specified rated voltage, current and specified temperature. Pay special attention to the maximum continuous temperature that the thermal fuse can withstand.
Additional suggestions and common problems:
Replacing fuses: When a thermal fuse burns out, it needs to be replaced with a new fuse with the same voltage and rated temperature. Usually, thermal fuses are designed to be push-pull, so you only need to gently pull out the old fuse and insert the new one.
Regular inspection: When using electrical appliances, electronic equipment, and automobiles, it is very important to regularly check whether the thermal fuse is burned out.
Име на продукта | Термичен предпазител, Температурен предпазител, Thermal Cutoff |
Материал на тялото | Plastic, Ceramic, Metal |
Rated Current | 1-30А |
Rated Voltage | 250V |
Lead Type | Axial, Radial |
Temperature | 70C-260C |
Application | Over-Temperature Protection |
Thermal cut-off fuses of different brands and types:
Свържете се с нас
Чакам вашия имейл, ние ще ви отговорим в рамките на 12 часа с ценна информация, от която се нуждаете.
СВЪРЗАНИ ПРОДУКТИ
Устройства за термично прекъсване на механичното съпротивление (Серия DF SF 10amp)
В последствие, напрежението между контактите на термичното прекъсване и DC веригата се повишава, за да се гарантира, че DC веригата е изключена. Чрез настоящото изобретение, проблемът, че термичното прекъсване в DC веригата не може ефективно да прекъсне веригата, е решен, и се постига ефектът от подобряване на безопасността на веригата.