Conjunto de sonda de sensor de termistor personalizado de China para control de temperatura

An NTC thermistor is a temperature sensor that uses the resistance properties of ceramic/metal composites to measure the temperature. Our full spectrum NTC thermistor is a resistance thermometer, or a resistor whose resistance is dependent on temperature. The term is a combination of “thermal” and “resistor”. It is made of metallic oxides, pressed into a bead, disk, or cylindrical shape and then encapsulated with an impermeable material such as epoxy or glass. Fabricante de sondas de sensor de resistencia de alta gama: YAXUN se especializa en termistores con sensibilidad a la temperatura y calificación AEC-Q200. TCTR – Termistor de película gruesa NTC. 47-1.6MΩ. Tolerancia más estricta 1%. Valor B 2410K – 4800k.
Sensor de temperatura de termistor: termistores lineales basados ​​en silicio al mismo costo y tamaño que los termistores NTC tradicionales. Logre la confiabilidad del sistema de alta precisión con los termistores lineales más pequeños de la industria.
Field-proven thermistor level-sensing technology with NPT mounting threads;
SP-M models temperature sensor are designed for use with ST-15 Control Monitors Electrical appliances, automóviles, aviación, small household appliances, toys;
Typical uses include storage tanks, double-containment piping trenches, and double-wall storage tank interstitial space monitoring;
Years of dependable, virtually maintenance-free operation;
Sensors can be easily extended to desired length at installation site using a 3/8” x 3/8” coupler and the required length of 3/8” NPT pipe.

Ender 3 Thermistor Sensor, Upgrade HT-NTC100K 3D Printer Thermistor Sensor: Thermistor temperature sensor. Metal head diameter: 3 milímetros, head length: 15 milímetros,cable wire length: 1 metro,conector: XH2.54 2PIN, （Suitable for heating blocks with holes of 3 mm*15 mm-3 mm*20 mm）;
Widly Compatibility: Product recommended operating temperature -50 °C ~ +280 °C, can replace the cartridge K-type thermocouple temperature sensor. Compatible with the heatblocks with 3 mm hole,como: V6 Volcano PT100 type heated block, etc.;
Sensors is accurate: The best feature was the flexible and heat shielded probe leads to the copper sensor. Unlike the other with a nickel plated probe/heat shrink, this can be fitted in very tight spots without worry. Be sure you redo your PID calibration;
Long Service Life: Compared with the same type that are insulated with ordinary heat shrinkable tubes, ours uses glass fiber with a temp resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temp work;
Fit ALL-METAL HOTEND: Work for E3D-V6 Volcano PT100 Ender 3 series all-metal hotend such as spider-hotend,K1-red-Lizard-hotend,dragonfly-hot-end,voron-hotend etc.

3Termistor de impresora D 100k NTC 3950 con 1 Uso del cable extendido del medidor para Ender 3 V2 Pro CR10 y otro hotend extrusor de impresora 3D

Heater NTC thermistor: with M3 Thread Stud thermistor，Fast-Plug Connector Compatible with 3/3 V2/3 Neo/3 V2 Neo/3S/3 PRO/5/5

Sensor termistor NTC100K para Creality 3 Actualización v2 3x15 mm 3950 Compatible con termistor

Radial Leaded Resin Coated NTC Thermistor Features
Alta precisión de medición.
Tight tolerance on resistance and Beta value.
Respuesta rápida, small dimension.
Can operate in long time stability.
Nominal resistance @25C can be from R25 1kΩ–1000kΩ.
Typical resistance at 25C R25 1k ohm, 2k ohmios, 2252 ohm, 3k ohmios, 4.7k ohmios, 5k ohmios, 6.8k ohmios, 10k ohmios, 15k ohmios, 20k ohmios, 30k ohmios, 40k ohmios, 47k ohmios, 50k ohmios, 100k ohmios, 150k ohmios, 1000k ohmios, etc..
Dissipation factor: ≥3.0 mW/C in still air.
Constante de tiempo térmico: ≤12 seconds in still air.
Rango de temperatura de funcionamiento: -45C — +125C.

Notas：□ in the part number for filling in resistance tolerance,
optional for ±1%(F), ±2%(GRAMO), ±3%(h), or ±5%(j).