Termékkategóriák
- Elektromos biztosíték 14
- Termikus áramkör megszakító 20
- Biztosítékdoboz-tartó 36
- Hőmérséklet érzékelő 67
- Hőkapcsoló 64
- Autó biztosíték 19
- Csavarja le a biztosítékokat 7
- hőbiztosíték 32
- felületre szerelhető biztosítékok 12
- termisztor 22
- PCB-re szerelhető biztosítéktartó 27
- Kábelköteg 6
- Penge biztosítéktartók 17
- termosztát 46
Termékcímkék
Csere Hi-limit Cut off termosztát & Visszaállítható hőkapcsoló
KSD301, KD302, KSD306, KD308 Hi-limit Cut off termosztát & Visszaállítható hőkapcsoló Amikor az áramkör megfelelően működik, az érintkezők zárt állapotban vannak. A névleges üzemi hőmérséklet elérésekor, a bimetál hő hatására deformálódik és gyorsan eltörik, az áramkör levágása. Ezek után, a készülék elkezd lehűlni.
Hi-limit Cut off Thermostat & Visszaállítható hőkapcsoló Amikor az áramkör megfelelően működik, az érintkezők zárt állapotban vannak. A névleges üzemi hőmérséklet elérésekor, a bimetál hő hatására deformálódik és gyorsan eltörik, az áramkör levágása. Ezek után, a készülék elkezd lehűlni. When it reaches the specified reset temperature, the bimetallic strip and spring strip snap back to their starting position, the contacts will close again, and the device will start working again.
Replacement Resettable Thermal Cutoff Switch process:
Multi-mount Manual Reset High Temp Limit Safety Switch L350°f For heater.
The fuse on the heater is a safety device. The hi-limit thermostat should control the temperature so that the fuse does not blow. Therefore if the fuse does blow the hi-limit thermostat is not regulating the temperature so it is assumed that it is toast. Note that the hi-limit thermostat is also just a safety device.
If the unit is running on the hi-limit thermostat, this indicates a problem as the hi-limit thermostat should not be regulating heater temperature, the cycling thermostat on the blower should be doing this.
You may have a grounded element (the element has sagged or broken and is touching the case) in which case none of the Hi-limit Cut off thermostats can regulate the temperature. Often you can see this by inspecting the heater assembly.
It can be checked with a meter.
Unplug the unit and remove the wires from the heater. Measure the heater should be around 10 ohmok. Then measure from each connector to the case/frame both should be infinite ohms (open).
Another possibility is a restriction or leak in the air flow inside the unit.
The dryer is actually sucking air over the heating coils, through the drum and then pushing the air out the exhaust. If the lint filter is coated with fabric softener residue this can reduce the air flow significantly causing the heater to run hot.
Also the operating/cycling Hi-limit Cut off thermostat is on the blower wheel so if the unit is sucking in air through a blown seal, it sees a cooler temperature at the blower and again causes the heater to run hot.
Beír | Hi-limit Cut off Thermostat & Visszaállítható hőkapcsoló |
Termék neve | KSD301 KSD302 KSD306 KSD314 electric motor Hi-limit Cut off Thermostat & Visszaállítható hőkapcsoló |
Rating Current | 5A-60A |
Rating Voltage | 250V |
Certificate | ROHS CQC CCC TUV VDE |
Visszaállítás típusa | Automatic/Manual Reset |
Alkalmazás | Small Home Appliance, stb. |
Condition | Normal Open/Close, Kézikönyv / automatikus visszaállítás |
Anyag | Műanyag, Ceramic/Metel Shell |
Packing | A táskán, Carton |
Lépjen kapcsolatba velünk
Várom az e-mailedet, belül válaszolunk 12 óra értékes információkkal, amelyekre szüksége van.