中国温度制御用カスタム サーミスタ センサー プローブ アセンブリ

An NTC thermistor is a temperature sensor that uses the resistance properties of ceramic/metal composites to measure the temperature. Our full spectrum NTC thermistor is a resistance thermometer, or a resistor whose resistance is dependent on temperature. The term is a combination of “thermal” and “resistor”. It is made of metallic oxides, pressed into a bead, disk, or cylindrical shape and then encapsulated with an impermeable material such as epoxy or glass. ハイエンド抵抗センサープローブメーカー — YAXUN は、温度感度と AEC-Q200 認定を備えたサーミスターを専門としています。. TCTR – NTC厚膜サーミスタ. 47-1.6MΩ. 最も厳しい公差 1%. B値2410K – 4800K.
サーミスタ温度センサー — 従来の NTC サーミスタと同じコストとサイズのシリコンベースのリニア サーミスタ. 業界最小のリニアサーミスタで高精度のシステム信頼性を実現.
Field-proven thermistor level-sensing technology with NPT mounting threads;
SP-M models temperature sensor are designed for use with ST-15 Control Monitors Electrical appliances, 自動車, aviation, small household appliances, toys;
Typical uses include storage tanks, double-containment piping trenches, and double-wall storage tank interstitial space monitoring;
Years of dependable, virtually maintenance-free operation;
Sensors can be easily extended to desired length at installation site using a 3/8” x 3/8” coupler and the required length of 3/8” NPT pipe.

Ender 3 Thermistor Sensor, Upgrade HT-NTC100K 3D Printer Thermistor Sensor: Thermistor temperature sensor. Metal head diameter: 3 んん, head length: 15 んん,cable wire length: 1 meter,コネクタ: XH2.54 2PIN, （Suitable for heating blocks with holes of 3 mm*15 mm-3 mm*20 mm）;
Widly Compatibility: Product recommended operating temperature -50 °C ~ +280 ℃, can replace the cartridge K-type thermocouple temperature sensor. Compatible with the heatblocks with 3 mm hole,のような: V6 Volcano PT100 type heated block, 等;
Sensors is accurate: The best feature was the flexible and heat shielded probe leads to the copper sensor. Unlike the other with a nickel plated probe/heat shrink, this can be fitted in very tight spots without worry. Be sure you redo your PID calibration;
Long Service Life: Compared with the same type that are insulated with ordinary heat shrinkable tubes, ours uses glass fiber with a temp resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temp work;
Fit ALL-METAL HOTEND: Work for E3D-V6 Volcano PT100 Ender 3 series all-metal hotend such as spider-hotend,K1-red-Lizard-hotend,dragonfly-hot-end,voron-hotend etc.

3D プリンタサーミスタ 100k NTC 3950 と 1 エンダー用メーター延長ケーブルワイヤー使用 3 V2 Pro CR10 およびその他の 3D プリンター押出機ホットエンド

Heater NTC thermistor: with M3 Thread Stud thermistor，Fast-Plug Connector Compatible with 3/3 V2/3 Neo/3 V2 Neo/3S/3 PRO/5/5

創造性のための NTC100K サーミスタ センサー 3 v2 アップグレード 3x15mm 3950 サーミスター対応

Radial Leaded Resin Coated NTC Thermistor Features
High measurement accuracy.
Tight tolerance on resistance and Beta value.
Fast response, small dimension.
Can operate in long time stability.
Nominal resistance @25C can be from R25 1kΩ–1000kΩ.
Typical resistance at 25C R25 1k ohm, 2kオーム, 2252 ohm, 3kオーム, 4.7kオーム, 5kオーム, 6.8kオーム, 10kオーム, 15kオーム, 20kオーム, 30kオーム, 40kオーム, 47kオーム, 50kオーム, 100kオーム, 150kオーム, 1000kオーム, 等.
Dissipation factor: ≥3.0 mW/C in still air.
Thermal time constant: ≤12 seconds in still air.
使用温度範囲: -45C — +125C.

Notes：□ in the part number for filling in resistance tolerance,
optional for ±1%(F), ±2%(G), ±3%(H), or ±5%(J).