KSD301 バイメタルセンサーサーマルスイッチ, カスタムバイメタルセンサーサーモスタット

The KSD301 125v / 250v 16 Amp Series Auto / Manual Reset Bimetal temperature control Thermostat is specifically designed for appliances with over-heat protection and prevention of excessive temperature rise. It can be customized sensor thermal switch to Auto reset below the low temperature of -35 ℃～280℃, or Manual reset. It can be used in the appliance with excessive temperature protection such as toasters, オーブン, Water heater, copy machine sand printers to name a few.

KSD301 Thermostat Bimetal Snap Disc Temperature Switch for Microwave, オーブン, コーヒーメーカー

Temperature Controller Rice Cooker Adjustable Bimetal Thermostat Sensor

温度制御スイッチ KSD301 ノーマルオープン 0 度250V 10Aサーモスタット

1. KSD301 temperature protector’s Principle and structure
The main principle of KSD series thermostat is that one function of bimetal discs is snap action under the change of sensing temperature. The snap action of disc can push the action of the contacts through the inside structure, and then caused on of off the circuit finally. The main characteristic are the fixation of working temperature, the reliable snap action, less flashover longer working life and less radio interference.

2. KSD301 bimetal thermostat’s specification
2.1. 電気定格: AC125V最大15A; AC250V 5A 10A 15A 最大 16A
2.2. 動作温度: -10～300度
2.3. 回復温度と作用温度の違い: 10 に 25 度, またはクライアントの要求に応じて.
2.4. 温度偏差: +-3 / +-5 / +-10 学位またはクライアントの要求に従って
2.5. 回路抵抗: ≤50mΩ (初期値)
2.6. 絶縁抵抗: ≧100mΩ (DC500V 通常状態)
2.7. 絶縁耐力: AC50Hz 1500V / 分, 故障による失明はありません (通常の状態)
ライフサイクル: ≥100000
2.8. 通常クローズまたはオープン
2.9. 2種類の取付金具: 可動または固定
2.10. ターミナル
ある. 端子の種類: 1874.8×0.5mmと4.8×0.8mmのシリーズ, 250 6.3×0.8mmのシリーズ
b. 端子角: 曲げ角度: 0~90°C オプション
2.11. ボディは2種類: プラスチックまたはセラミック.
2.12. 2種類の温度センサー面: アルミニウムキャップまたは銅ヘッド.

3. Difference of bimetal thermostat auto reset type and Manual reset type
3.1. Manual reset type: Temperature sensing components consist of bimetallic strip. When the temperature reached the action temperature range, it will jump quickly and the movable disc disconnects. When the temperature declines to a fixed temperature point, the contact point cannot reset until reconnecting the circuit by pushing the reset button. And then the contact points recover, reaching a purpose of connecting or disconnecting the circuit and restarting the circuit by manual reset. (Kindly reminder: 1.This type of manual reset thermostat can reset when the temperature declines 20 °C after snap action by pressing the reset button. And 4~6 N will be advisable; please don’t use too much strength.
2. To ensure the normal function, the distance between the reset button and the close cover should not be less than 20.4mm. )
3.2. Manual reset type: Temperature sensing components consist of bimetallic strip. When the temperature reached the action temperature range, it will jump quickly and the movable disc disconnects. When the temperature declines to a fixed temperature point, the contact point can auto reset and start working.

KSD301 bimetal thermostat’s Application
It is used as temperature control for household electric appliances and widely applied in coffee pots, automatic toasters, ラミネーター, electric water pots, steam guns, steam irons, wind warmers, 電子レンジ, ウォーターサーバー, 等.

KSD301 bimetal thermostat’s Open temperature & 温度をリセットする
1. お客様のご要望に応じて開放温度とリセット温度を設定します.
2. オートリセットタイプの標準開放温度と復帰温度シートは以下の通りです

The product UL,CQC,VDE and RoHS certification approval.