중국 온도 조절을 위한 맞춤형 서미스터 센서 프로브 어셈블리

An NTC thermistor is a temperature sensor that uses the resistance properties of ceramic/metal composites to measure the temperature. Our full spectrum NTC thermistor is a resistance thermometer, or a resistor whose resistance is dependent on temperature. The term is a combination of “thermal” and “resistor”. It is made of metallic oxides, pressed into a bead, disk, or cylindrical shape and then encapsulated with an impermeable material such as epoxy or glass. 고급 저항 센서 프로브 제조업체 - YAXUN은 온도 감도 및 AEC-Q200 인증을 갖춘 서미스터 전문 업체입니다.. TCTR – NTC 후막 서미스터. 47-1.6MΩ. 가장 엄격한 허용 오차 1%. B값 2410K – 4800케이.
서미스터 온도 센서 - 기존 NTC 서미스터와 동일한 비용 및 크기의 실리콘 기반 선형 서미스터. 업계 최소형 선형 서미스터로 고정확도 시스템 신뢰성 달성.
Field-proven thermistor level-sensing technology with NPT mounting threads;
SP-M models temperature sensor are designed for use with ST-15 Control Monitors Electrical appliances, 자동차, 비행, small household appliances, toys;
Typical uses include storage tanks, double-containment piping trenches, and double-wall storage tank interstitial space monitoring;
Years of dependable, virtually maintenance-free operation;
Sensors can be easily extended to desired length at installation site using a 3/8” x 3/8” coupler and the required length of 3/8” NPT pipe.

Ender 3 Thermistor Sensor, Upgrade HT-NTC100K 3D Printer Thermistor Sensor: Thermistor temperature sensor. Metal head diameter: 3 mm, head length: 15 mm,cable wire length: 1 meter,커넥터: XH2.54 2PIN, （Suitable for heating blocks with holes of 3 mm*15 mm-3 mm*20 mm）;
Widly Compatibility: Product recommended operating temperature -50 ℃ ~ +280 ℃, can replace the cartridge K-type thermocouple temperature sensor. Compatible with the heatblocks with 3 mm hole,~와 같은: V6 Volcano PT100 type heated block, 등;
Sensors is accurate: The best feature was the flexible and heat shielded probe leads to the copper sensor. Unlike the other with a nickel plated probe/heat shrink, this can be fitted in very tight spots without worry. Be sure you redo your PID calibration;
Long Service Life: Compared with the same type that are insulated with ordinary heat shrinkable tubes, ours uses glass fiber with a temp resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temp work;
Fit ALL-METAL HOTEND: Work for E3D-V6 Volcano PT100 Ender 3 series all-metal hotend such as spider-hotend,K1-red-Lizard-hotend,dragonfly-hot-end,voron-hotend etc.

3D 프린터 서미스터 100k NTC 3950 ~와 함께 1 Ender용 미터 확장 케이블 와이어 사용 3 V2 Pro CR10 및 기타 3D 프린터 압출기 핫엔드

Heater NTC thermistor: with M3 Thread Stud thermistor，Fast-Plug Connector Compatible with 3/3 V2/3 Neo/3 V2 Neo/3S/3 PRO/5/5

Creality용 NTC100K 서미스터 센서 3 v2 업그레이드 3x15mm 3950 서미스터 호환

Radial Leaded Resin Coated NTC Thermistor Features
High measurement accuracy.
Tight tolerance on resistance and Beta value.
빠른 응답, small dimension.
Can operate in long time stability.
Nominal resistance @25C can be from R25 1kΩ–1000kΩ.
Typical resistance at 25C R25 1k ohm, 2케이 옴, 2252 ohm, 3케이 옴, 4.7케이 옴, 5케이 옴, 6.8케이 옴, 10케이 옴, 15케이 옴, 20케이 옴, 30케이 옴, 40케이 옴, 47케이 옴, 50케이 옴, 100케이 옴, 150케이 옴, 1000케이 옴, 등.
Dissipation factor: ≥3.0 mW/C in still air.
열시상수: ≤12 seconds in still air.
작동 온도 범위: -45C — +125C.

메모：□ in the part number for filling in resistance tolerance,
optional for ±1%(에프), ±2%(G), ±3%(시간), or ±5%(제이).