Kategorie produktów
- bezpiecznik termiczny 32
- bezpieczniki do montażu powierzchniowego 12
- termistor 17
- Uchwyt bezpiecznika do montażu na płytce drukowanej 27
- Wiązka przewodów 4
- Uchwyty bezpieczników ostrza 17
- termostat 46
- Bezpiecznik elektryczny 14
- Wyłącznik termiczny 20
- Uchwyt skrzynki bezpieczników 36
- Czujnik temperatury 58
- Wyłącznik termiczny 64
- Bezpiecznik samochodowy 19
- Przykręcić bezpieczniki 7
Tagi produktów
Ostatnie posty
SEFUSE NEC SF Cutoffs Thermal Fuse OEM/ODM Service
How to tell if a sefuse NEC temperature fuse (Bezpiecznik termiczny) is good or bad?
The following steps can be used to measure the quality of a temperature fuse (Bezpiecznik termiczny) :
Use a multimeter to measure the resistance value: Set the multimeter to the resistance value measurement position, and then connect two test pens to the two ends of the Thermal Fuse . If the fuse is not blown, its resistance value should be very small. If the fuse is blown, the resistance value will be a larger number. If you are not sure about the correct resistance value, you can refer to the product manual or consult the manufacturer.
![]() SF240E SEFUSE NEC Cutoffs Thermal Fuse OEM ODM Service |
![]() SF96E SEFUSE Cutoffs NEC Thermal Fuse 99 Degree 10A 250V |
![]() SCHOTT SEFUSE® – Reliable thermal fuses for the protection |
Observe the color change: If the Thermal Fuse turns black or the resistance value is abnormally high, it needs to be replaced.
The following matters need to be noted during the measurement process:
Lead bending: When bending the lead, it should be bent from a part more than 6 mm away from the root, and the root and lead should not be damaged. Do not forcibly pull, press, or twist the lead.
Welding operation: When welding the lead, the heating humidity should be limited to a minimum, and be careful not to apply high temperature to the thermal fuse. Do not forcibly pull, press, or twist the thermal fuse and lead. After welding, it should be cooled for more than 30 seconds immediately.
Use conditions: Thermal fuses can only be used under the conditions of specified rated voltage, current and specified temperature. Pay special attention to the maximum continuous temperature that the thermal fuse can withstand.
Additional suggestions and common problems:
Replacing fuses: When a thermal fuse burns out, it needs to be replaced with a new fuse with the same voltage and rated temperature. Zazwyczaj, thermal fuses are designed to be push-pull, so you only need to gently pull out the old fuse and insert the new one.
Regular inspection: When using electrical appliances, electronic equipment, and automobiles, it is very important to regularly check whether the thermal fuse is burned out.
Product Name | Bezpiecznik termiczny, Bezpiecznik temperaturowy, Odcięcie termiczne |
Body Material | Plastic, Ceramic, Metal |
Rated Current | 1-30A |
Napięcie znamionowe | 250V |
Lead Type | Axial, Promieniowy |
Temperature | 70C-260C |
Application | Over-Temperature Protection |
Thermal cut-off fuses of different brands and types:
![Black Square 250V Thermal Fuse Cutoff LED Fuses](https://www.powerswitchcn.com/wp-content/uploads/2024/08/Black-Square-250V-Thermal-Fuse-Cutoff-LED-Fuses.jpg)
Black Square 250V Thermal Fuse Cutoff LED Fuses
![250V Circuit Cut-off Temperature Thermal Fuse Ceramics](https://www.powerswitchcn.com/wp-content/uploads/2024/08/250V-Circuit-Cut-off-Temperature-Thermal-Fuse-Ceramics.jpg)
250V Circuit Cut-off Temperature Thermal Fuse Ceramics
![SEFUSE NEC SF Cutoffs Thermal Fuse](https://www.powerswitchcn.com/wp-content/uploads/2024/08/SEFUSE-NEC-SF-Cutoffs-Thermal-Fuse.jpg)
SEFUSE NEC SF Cutoffs Thermal Fuse
Skontaktuj się z nami
Czekam na Twój e-mail, odpowiemy Ci w ciągu 12 godziny z cennymi informacjami, których potrzebujesz.