Китайский изготовленный на заказ датчик термистора в сборе с датчиком для контроля температуры

An NTC thermistor is a temperature sensor that uses the resistance properties of ceramic/metal composites to measure the temperature. Our full spectrum NTC thermistor is a resistance thermometer, or a resistor whose resistance is dependent on temperature. The term is a combination of “thermal” and “resistor”. It is made of metallic oxides, pressed into a bead, disk, or cylindrical shape and then encapsulated with an impermeable material such as epoxy or glass. Производитель высококлассных резисторных датчиков-датчиков — YAXUN специализируется на термисторах с температурной чувствительностью и сертификацией AEC-Q200.. ТКТР – Толстопленочный термистор NTC. 47-1.6МОм. Самый строгий допуск 1%. Значение Б 2410К – 4800К.
Термисторный датчик температуры — линейные термисторы на основе кремния по той же стоимости и размеру, что и традиционные термисторы NTC. Обеспечьте высокую надежность системы с помощью самых маленьких в отрасли линейных термисторов.
Field-proven thermistor level-sensing technology with NPT mounting threads;
SP-M models temperature sensor are designed for use with ST-15 Control Monitors Electrical appliances, автомобили, авиация, small household appliances, toys;
Typical uses include storage tanks, double-containment piping trenches, and double-wall storage tank interstitial space monitoring;
Years of dependable, virtually maintenance-free operation;
Sensors can be easily extended to desired length at installation site using a 3/8” x 3/8” coupler and the required length of 3/8” NPT pipe.

Ender 3 Thermistor Sensor, Upgrade HT-NTC100K 3D Printer Thermistor Sensor: Датчик температуры термистора. Metal head diameter: 3 мм, head length: 15 мм,cable wire length: 1 meter,разъем: XH2.54 2PIN, （Suitable for heating blocks with holes of 3 mm*15 mm-3 mm*20 mm）;
Widly Compatibility: Product recommended operating temperature -50 °C ~ +280 °С, can replace the cartridge K-type thermocouple temperature sensor. Compatible with the heatblocks with 3 mm hole,такой как: V6 Volcano PT100 type heated block, и т. д.;
Sensors is accurate: The best feature was the flexible and heat shielded probe leads to the copper sensor. Unlike the other with a nickel plated probe/heat shrink, this can be fitted in very tight spots without worry. Be sure you redo your PID calibration;
Long Service Life: Compared with the same type that are insulated with ordinary heat shrinkable tubes, ours uses glass fiber with a temp resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temp work;
Fit ALL-METAL HOTEND: Work for E3D-V6 Volcano PT100 Ender 3 series all-metal hotend such as spider-hotend,K1-red-Lizard-hotend,dragonfly-hot-end,voron-hotend etc.

3D Термистор принтера 100k NTC 3950 с 1 Использование удлиненного кабеля для Ender 3 V2 Pro CR10 и другие экструдеры для 3D-принтеров Hotend

Heater NTC thermistor: with M3 Thread Stud thermistor，Fast-Plug Connector Compatible with 3/3 V2/3 Neo/3 V2 Neo/3S/3 PRO/5/5

Термисторный датчик NTC100K для Creality 3 v2 Обновление 3x15 мм 3950 Совместимость с термисторами

Radial Leaded Resin Coated NTC Thermistor Features
High measurement accuracy.
Tight tolerance on resistance and Beta value.
Fast response, small dimension.
Can operate in long time stability.
Nominal resistance @25C can be from R25 1kΩ–1000kΩ.
Typical resistance at 25C R25 1k ohm, 2кОм, 2252 ohm, 3кОм, 4.7кОм, 5кОм, 6.8кОм, 10кОм, 15кОм, 20кОм, 30кОм, 40кОм, 47кОм, 50кОм, 100кОм, 150кОм, 1000кОм, и т. д..
Dissipation factor: ≥3.0 mW/C in still air.
Thermal time constant: ≤12 seconds in still air.
Диапазон рабочих температур: -45C — +125C.

Notes：□ in the part number for filling in resistance tolerance,
optional for ±1%(Ф), ± 2%(G), ±3%(ЧАС), or ±5%(Дж).