Датчик температуры NTC с соединительной линией клеммы Overmolding

Датчик температуры NTC с разъемом для формования (японское стандартное время, Молекс, RJ11, RJ12, RJ45, RJ50, XH, СМ, PH, Авиационная вилка, клеммные колодки, 5557, Терминал Фастон, аудиоразъем, и т. д.). Головка датчика изготовлена ​​из материала TPE., который имеет хорошую адгезию и герметизацию. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. Головка датчика изготовлена ​​из материала TPE., который имеет хорошую адгезию и герметизацию. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

ТПЭ Формование10K 3950 Кабель датчика температуры резервуара для воды С аудиоразъемом 6,35 мм

Датчик NTC из нержавеющей стали с разъемом TPE Overmolding

Waterproof NTC, ПТ100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, и т. д.. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, micro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. При использовании, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. After powering on, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

Примечание: Although the product can work normally at 125°C. Однако, since the cable is made of polyvinyl chloride (ПВХ) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

Описание

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

Services
1. Your inquiry will be replied within 24 часы;
2. Well-trained and experienced staff are always at your service.
3. Unique design products and many private mold product are waiting for your choice.
4. Strictly protect your private information and your ideas of design.
Часто задаваемые вопросы

Q1. Can I have a sample order for NTC, PT100,PT1000, РДД, and Ds18b20 SENSOR?
А: Да, we welcome sample order to test and check quality. Mixed samples are acceptable.