10En 250V RY RH temperatursäkring för riskokare, Elektrisk fläkt

10En 250V RY RH termisk säkring före åtgärd:
The metal shell of the SF type overheat fuse contains a movable electrode, a spring and a thermistor. Spring B is installed in a compressed state, and the spring force is used to make lead A, movable electrode, metal shell and lead B conductive.

After the RY RH thermal fuse is activated:
When the ambient temperature exceeds the fuse action temperature, the heat transferred through the metal shell melts the thermistor particles, and springs A and B are both extended, but the elastic force in the A direction is large, forcing spring B to press toward the B side, thereby disconnecting lead A and the movable electrode to cut off the circuit.

2: Thermal circuit breaker (SM type)
The low melting point alloy is installed in the ceramic shell as a heat-sensitive material. Its cut-off current is 0.5A, 1A, and 2A. It has the advantage of being directly installed at the temperature detection location.

Sanyuan termisk säkring RY-serien temperatursäkring 250V 10A

quality Alloy Type 250V 10A, 15A, 20A Square Thermal Fuses

10A,20A,16En 250V RY RH termisk säkringslänkar

Principle:
Before action:
Lead A and lead B are connected to the circuit together with the fusible element. The outer surface of the rotator is covered with flux.
After operation:
The temperature of the fusible material rises with the rise of the ambient temperature, and it melts soon. Under the action of the flux and the surface tension of the fusible material, it instantly forms a ball, thereby cutting off the circuit.

4. Features and uses
1. Funktioner:
a. Because of its small size, it is very sensitive to the ambient temperature.
b. Due to its airtight structure, the change caused by aging is very small, and it has a very high operating temperature.
c. It is a non-recovery type, and it will not recover even if the temperature drops after operation.
2. Uses:
I. Electric stoves, electric hot tables, electric carpets, kerosene fan heaters, warm air blowers.
I. Electric irons, trouser presses, hot hair dryers, hårtorkar, rechargeable shavers.
III. Air conditioners, ventilating fans, tvättmaskiner, etc.
V. Refrigerators, color TVs, fluorescent lamps, etc.
V. Electric rice cookers, grillar, kaffekannor, electric money cookers.

Common installation methods include:
Welding, splicing, and welding
(1) Installation position: mer än 5 mm from the fuse body.
(2) Do not allow the welding heat to cause the temperature to exceed the fuse action temperature during welding.
Solutions:
a. Clamp the tool or fixture near the shell to dissipate heat;
b. Shorten the operation time;
c. Reduce the welding temperature;
d. Weld away from the fuse body.
(3) Do not increase the resistance during splicing or welding.
If the resistance of the connection part is too large, abnormal heating will cause the fuse to operate when the power is turned on. Especially in splicing situations, the resistance will increase due to thermal cycles or temperature.
(4) After installation, do not pull, press, or twist the lead wire.
(5) Do not allow the resin-sealed lead wire to contact the fuse body. If contact is made, the current can be transmitted to the other end through the metal shell, and the purpose of cutting off the circuit cannot be achieved.
(6) The SF type cannot contact the metal part of the installation part.
(7) When crimping, the rear part cannot be loose, and copper crimping terminals are suitable.
(8) The installation location should be where the machine is prone to failure and generates the most abnormal heat.

Produktbeskrivning

DYE 250V 15A 16A Thermal Cutoff Fuse Thermal Cutout Link DF104S DF184S DF192S

Produktbeskrivning

The Thermal DF Series Thermal Cutoffs are single action devices that open when

a preset temperature is reached. They do not reset. The active component of a thermal

cutoff is an electrically insulated thermal pellet. This pellet holds a spring loaded

contact against a fixed contact under normal operating temperatures. (See Fig. 1)

When the preset temperature of the cutoff is reached, the pellet liquifies, the springs

relax, and the spring loaded contact is moved away from the fixed contact, opening the

circuit. The DF Series is the right choice for applications requiring an inexpensive

limit protector with 15A capability.

Product Features

Märkström: UL 250V 10A/16A, VDE 15A, CCC 15A

Advantage: One shot operation, stable and precise, compact, durable and reliable by hermetic seal structure, excellently sensitive to ambient temperature.

Fungera: Termisk säkring, Widely Used in Electric Current Appliance as Heat Protection. When temperatures exceed the specified TF level, Electrical Contacts will Open.

Ansökningar: Suitable for electric home appliances, electric industrial equipment, office automation equipment, plain paper copiers, transformatorer, motorer, etc.

Specifikation

(SEFUSE SF-E thermal fuse, thermal cutoff, thermal link)

Opening Temperature Tolerance: TF+0°C/-5°C

Temperature Rating (Tf):Rated opening temperature

Holding temperature (Th):Maximum temperature measured at the case end ofthe thermal cutoff at which the thermal cutoff can be maintained for a period for 168 hours without opening.

Maximum temperature (Tm):The maximum temperature at which a thermal cutoff can be maintained for10 minutes as an open circuit and can then be maintained at twice rated voltage for a period of 2 minutes during which its mechanical and electrical properties will not be impaired