Cảm biến nhiệt độ NTC với Đường dây kết nối đầu cuối ép xung

Đầu dò cảm biến nhiệt độ NTC với đầu nối ép xung (JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Ổ cắm hàng không, khối thiết bị đầu cuối, 5557, Nhà ga Faston, giắc âm thanh, vân vân). Đầu cảm biến được làm từ chất liệu TPE, có độ bám dính và niêm phong tốt. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. Đầu cảm biến được làm từ chất liệu TPE, có độ bám dính và niêm phong tốt. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

Đúc TPE10K 3950 cáp cảm biến nhiệt độ bể nước Có phích cắm âm thanh 6,35mm

Cảm biến NTC bằng thép không gỉ với đầu nối TPE Overmolding

Subject	Đặc điểm kỹ thuật	More options
Sensor	NTC 10KΩ	NTC 10K, NTC 50KΩ, NTC 100KΩ, PT100, PT1000, DS18B20, vân vân.
Cáp	TPE cable	PVC cable, PU cable, silicone cable, vân vân.
Đầu nối	Nothing	JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Ổ cắm hàng không, khối thiết bị đầu cuối, 5557, Nhà ga Faston, giắc âm thanh, vân vân.
Precision	1%	1,5%, 2%, 2,5%, 3%, vân vân.
IP class	IP68	IP65, IP66, IP68, vân vân.

Waterproof NTC, PT100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, vân vân. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, micro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. Khi sử dụng, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. After powering on, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

Ghi chú: Although the product can work normally at 125°C. Tuy nhiên, since the cable is made of polyvinyl chloride (PVC) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

Đầu dò cảm biến rã đông cảm biến nhiệt độ đóng băng

Sự miêu tả

TYPE:	TPE Plastic Overmolding sensor	B25/50:	3950K, 3977K, 3435K
Sensor Head:	O Ring, Fork Metal, Injected Tube, NPT, M16, tainless Steel Tube	Dây điện:	CL2 PT4,#24 2466,#28 1332
Cách sử dụng:	Refrigerator Defrost Sensor, Instant Water Heaters, máy nước nóng, air conditioner, refrigerator, water fountain, induction cooker, coffee maker	Pn (rated Power):	50mw
Điểm nổi bật:	EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC thermistor Sensor, TPE Plastic Overmolding sensor

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

Specification Name	Scope	Detection Condition
R25(nominal resistance value)	1k, 2k, 2.7k, 3k, 5k, 10k, 15k, 20k, 30k, 40k, 47k, 50k, 100k, 200k (EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC thermistor)	Constant temperature 25℃±0.05℃
R25 Permissible variance(%)	±1,±2, ±3, ±5, ±10	Constant temperature 25℃±0.05℃
B25/50 or B25/85(material coefficient)(thermal-sensitivity index)	2500~5000K	Constant temperature 25℃±0.05℃ Constant temperature 85℃±0.05℃
B25/50 Value permissible variance(%)	±1,±2	Constant temperature 25℃±0.05℃ Constant temperature 50℃±0.05℃
∫(dissipation coefficient)	≥0.8mw/℃	Static in the air
T(thermal time constant)	≤25S	Static in the air
Ta(Working temperature)	-30℃~+120℃
Pn (rated power)	50mw	within working temperature
Case and head		Fork head, O ring head,drops of water head, Metal case, Thread copper case, injection head, tainless Steel Tube, or according to client’s drawing
Lead wire		#24 30# 2651, UL4411 28#, double wired conductor and so on, or according to client’s request.
Terminal		Can be riveted according to the requirements of various terminals

Services
1. Your inquiry will be replied within 24 hours;
2. Well-trained and experienced staff are always at your service.
3. Unique design products and many private mold product are waiting for your choice.
4. Strictly protect your private information and your ideas of design.
Câu hỏi thường gặp

Q1. Can I have a sample order for NTC, PT100,PT1000, RTD, and Ds18b20 SENSOR?
MỘT: Đúng, we welcome sample order to test and check quality. Mixed samples are acceptable.