中国定制热敏电阻传感器探头组件，用于温度控制

An NTC thermistor is a temperature sensor that uses the resistance properties of ceramic/metal composites to measure the temperature. Our full spectrum NTC thermistor is a resistance thermometer, or a resistor whose resistance is dependent on temperature. The term is a combination of “thermal” and “resistor”. It is made of metallic oxides, pressed into a bead, disk, or cylindrical shape and then encapsulated with an impermeable material such as epoxy or glass. 高端电阻传感器探针制造商——亚迅专业生产热敏电阻，具有温度敏感性，符合AEC-Q200标准. TCTR – NTC厚膜热敏电阻. 47-1.6兆欧姆. 最严格的公差 1%. B值2410K – 4800K.
热敏电阻温度传感器 — 硅基线性热敏电阻，成本和尺寸与传统 NTC 热敏电阻相同. 利用业界最小的线性热敏电阻实现高精度系统可靠性.
Field-proven thermistor level-sensing technology with NPT mounting threads;
SP-M models temperature sensor are designed for use with ST-15 Control Monitors Electrical appliances, 汽车, 航空, small household appliances, toys;
Typical uses include storage tanks, double-containment piping trenches, and double-wall storage tank interstitial space monitoring;
Years of dependable, virtually maintenance-free operation;
Sensors can be easily extended to desired length at installation site using a 3/8” x 3/8” coupler and the required length of 3/8” NPT pipe.

Ender 3 Thermistor Sensor, Upgrade HT-NTC100K 3D Printer Thermistor Sensor: Thermistor temperature sensor. Metal head diameter: 3 毫米, head length: 15 毫米,cable wire length: 1 meter,连接器: XH2.54 2PIN, （Suitable for heating blocks with holes of 3 mm*15 mm-3 mm*20 mm）;
Widly Compatibility: Product recommended operating temperature -50 ℃~ +280 ℃, can replace the cartridge K-type thermocouple temperature sensor. Compatible with the heatblocks with 3 mm hole,例如: V6 Volcano PT100 type heated block, ETC;
Sensors is accurate: The best feature was the flexible and heat shielded probe leads to the copper sensor. Unlike the other with a nickel plated probe/heat shrink, this can be fitted in very tight spots without worry. Be sure you redo your PID calibration;
Long Service Life: Compared with the same type that are insulated with ordinary heat shrinkable tubes, ours uses glass fiber with a temp resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temp work;
Fit ALL-METAL HOTEND: Work for E3D-V6 Volcano PT100 Ender 3 series all-metal hotend such as spider-hotend,K1-red-Lizard-hotend,dragonfly-hot-end,voron-hotend etc.

3D 打印机热敏电阻 100k NTC 3950 和 1 米德延长电缆线使用 3 V2 Pro CR10 和其他 3D 打印机挤出机热端

Heater NTC thermistor: with M3 Thread Stud thermistor，Fast-Plug Connector Compatible with 3/3 V2/3 Neo/3 V2 Neo/3S/3 PRO/5/5

NTC100K 热敏电阻传感器带来创意 3 v2升级3x15mm 3950 兼容热敏电阻

Radial Leaded Resin Coated NTC Thermistor Features
测量精度高.
Tight tolerance on resistance and Beta value.
Fast response, small dimension.
Can operate in long time stability.
Nominal resistance @25C can be from R25 1kΩ–1000kΩ.
Typical resistance at 25C R25 1k ohm, 2千欧姆, 2252 ohm, 3千欧姆, 4.7千欧姆, 5千欧姆, 6.8千欧姆, 10千欧姆, 15千欧姆, 20千欧姆, 30千欧姆, 40千欧姆, 47千欧姆, 50千欧姆, 100千欧姆, 150千欧姆, 1000千欧姆, ETC.
Dissipation factor: ≥3.0 mW/C in still air.
Thermal time constant: ≤12 seconds in still air.
工作温度范围: -45C — +125C.

笔记：□ in the part number for filling in resistance tolerance,
optional for ±1%(F), ±2%(G), ±3%(H), or ±5%(J).