产品类别
产品标签
铠装热电偶传感器
刀片保险丝座
汽车插片保险丝
汽车保险丝
陶瓷管保险丝
断路器
盘式温控器
DS18b20 温度传感器
电气保险丝
快熔断/慢熔断保险丝
保险丝盒支架
玻璃管保险丝
直插式保险丝座
限位卡盘温控器
迷你断路器
电机过载保护器
电机热保护
NTC传感器
NTC热敏电阻传感器
PCB 安装保险丝座
PPTC自恢复保险丝
PT100温度传感器
正温度系数热敏电阻
传感器连接器线束
传感器探头 & 电缆
慢熔断微型保险丝
表面贴装保险丝
临时截止链接
温控开关
温度保险丝
温度感应器
温度传感器电缆
温度传感器探头
温度开关
热切断
热切断开关
热熔断器
热保护器
热敏开关
热敏电阻传感器探头
SEFUSE NEC SF 熔断器热熔断器 OEM/ODM 服务
How to tell if a sefuse NEC temperature fuse (热熔断器) is good or bad?
The following steps can be used to measure the quality of a temperature fuse (热熔断器) :
Use a multimeter to measure the resistance value: Set the multimeter to the resistance value measurement position, and then connect two test pens to the two ends of the Thermal Fuse . If the fuse is not blown, its resistance value should be very small. If the fuse is blown, the resistance value will be a larger number. If you are not sure about the correct resistance value, you can refer to the product manual or consult the manufacturer.
Observe the color change: If the Thermal Fuse turns black or the resistance value is abnormally high, it needs to be replaced.
The following matters need to be noted during the measurement process:
Lead bending: When bending the lead, it should be bent from a part more than 6 mm away from the root, and the root and lead should not be damaged. Do not forcibly pull, press, or twist the lead.
Welding operation: When welding the lead, the heating humidity should be limited to a minimum, and be careful not to apply high temperature to the thermal fuse. Do not forcibly pull, press, or twist the thermal fuse and lead. After welding, it should be cooled for more than 30 seconds immediately.
Use conditions: Thermal fuses can only be used under the conditions of specified rated voltage, current and specified temperature. Pay special attention to the maximum continuous temperature that the thermal fuse can withstand.
Additional suggestions and common problems:
Replacing fuses: When a thermal fuse burns out, it needs to be replaced with a new fuse with the same voltage and rated temperature. 通常, thermal fuses are designed to be push-pull, so you only need to gently pull out the old fuse and insert the new one.
Regular inspection: When using electrical appliances, electronic equipment, and automobiles, it is very important to regularly check whether the thermal fuse is burned out.
Product Name | 热熔断器, 温度保险丝, 热熔断器 |
机身材质 | Plastic, 陶瓷制品, Metal |
额定电流 | 1-30A |
额定电压 | 250V |
Lead Type | Axial, 径向 |
Temperature | 70C-260C |
应用 | Over-Temperature Protection |
Thermal cut-off fuses of different brands and types:
联系我们
等待您的电子邮件, 我们将在短时间内回复您 12 小时提供您需要的有价值的信息.
相关产品
Emerson G4 / G5 series microtemp 10A / 20A thermal fuse
Emerson Group production MICROTEMP® G4 G5 series thermal fuse, According to different product specifications, Rated load current, respectively, up to AC250V 10A, AC120V 15A and DC24V 5A. To provide reliable protection against overheating, In the same industry products, MICROTEMP® G4 G5 series thermal fuse has established its flagship status can not be shaken.